: .
top of page

LOW TEMPERATURE OUTDOOR REFRIGERATION SYSTEMS

Images are for illustrative purposes only

WALK-IN COOLER, WALK-IN FREEZER, OUTDOOR REFRIGERATION SYSTEMS FROM 1/2 HP TO 80 HP

2 HP LOW TEMPERATURE PRE-ASSEMBLED REMOTE OUTDOOR REFRIGERATION SYSTEM, R-404A REFRIGERANT (208-230 VOLTS, 60 Hz, 1 PHASE) (3 PHASE ELECTRICAL AVAILABLE UPON REQUEST) INCLUDES:

  • HERMETIC Copeland Compressor

  • Space saving, compact design

  • Energy efficient PSC condenser fan motor with overload protection

  • Quiet fan motor operation

  • Anti-Corrosion-Fins To Increase Coil Life Span

  • High efficiency enhanced tube condenser design

  • Seamless Inner Groove Copper Tubing For Increased Heat Exchange

  • Head Pressure Control To Stabilize The Freezing Of Liquid Line And Prevent Compressor Damage

  • Base mounted liquid and suction shut-off valves

  • Receiver Isolation valve with Pressure relief plug

  • Fan guard

  • Unit leak tested and shipped with nitrogen holding charge

  • Industry Standard Parts For Easy Replacement

  • Easily Accessible Special Wiring Harness Connections That Won't Come Loose With Vibration

  • Control Box And Service Valves Located Outside For Easy Installation And Service

  • Preassembled Outdoor Cover To Protect Against Corrosion - Pre-painted grey

  • Hydrogen leak and dielectric tested before shipping with Dry Nitrogen shipping charge (25 to 35 PSI)

  • Approved By U.L., C-UL And ISO9001

  • 208-230/60/1 Voltage

  • BTUs: 8,780 (When Holding At -10º F)

  • (1) Floo580 head pressure control

  • (1) Factory Mounted Sight Glass with moisture indicator

  • (1) Factory Mounted Drier

  • (1) Factory Mounted Encapsulated high and low pressure controls

  • (1) Thermostat (Loose)

  • (1) Solenoid Valve And Coil (Loose)

  • (1) Factory Mounted Crankcase heater

  • (1) Electronic defrost timer with defrost contactor/relay

  • on low temperature models

  • Dimensions L 28 1/4" x W 39 7/8" x H 21 1/4"

  • Standard One year compressor warranty

ELECTRIC DEFROST LOW PROFILE EVAPORATOR (208-230 VOLTS, 60 Hz, 1 PHASE) INCLUDES:

  • High efficiency motor(s)

  • (2) 12" Fans

  • Compact design with embossed Aluminum casing, lightweight yet durable

  • The unit is designed to mount flush to the ceiling and meets all NSF requirements

  • Each fan section is baffled to prevent short cycling of the air

  • Heavy duty 12" Aluminum fans are balanced to provide vibration-free operation

  • Ample electrical and header compartments

  • End panels slide out for easy serviceability from the front or ends of the unit

  • PSC motors or EC motors (available)

  • Sweat connections are standard on all models

  • Copper hairpins are staggered and mechanically expanded into corrugated Aluminum fins and tube sheets to achieve maximum heat transfer

  • Die formed fin collars provide even fin spacing

  • Positive slope drain pan

  • Central drain connections

  • Internal coil heaters provide rapid and efficient defrost

  • A lower heater is installed close to the drain pan for fast, reliable drainage

  • A defrost termination fan delay thermostat (DTFD) terminates the defrost cycle when the temperature is satisfied

  • A heater safety thermostat is installed to prevent heaters from overheating above 75°F.

  • Large 3/4" ODS (3/4" NTP) drain hole

  • Dimensions L 41 1/2" x D 15 1/8" x H 15"

  • Thermostatic expansion valve

  • System BTUH: 9,200 (When holding at -10° F)

bottom of page